LTP Rust Stain Remover 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Up to 5m2 per litre    Suitability: Ideal for all types of polished and unpolished natural and artificial stone including marble, granite, travertine, split face stone cladding, sandstone, concrete, terracotta and porcelain tiles You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here.

LTP Porcelain Tile Enhancer 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Around 30-40m2 (based on 1 coat) depending on substrate texture Suitability: A low-maintenance film-forming surface sealer and protector You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Do not over-apply as a heavy layer or with too many coats as it may cause unsightly build-up/affect slip resistance and/or reduce the efficiency of the product. Hardens after about an hour but will take a further 3 days to achieve full hardness and become fully resistant.

LTP Grout Haze and Limescale Remover 500ml

Colour: Clear Size (ml): 500ml Approximate Coverage: Cement based grout films, up to 10m2. Limescale and hardwater stains, up to 15m2    Suitability: Used as a first wash cleaner for removing cement-based grout haze from the surface of tiles without affecting the joint You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Not suitable for use on stone surfaces that are polished (ie. polished marble, travertine or limestone). Sealed natural stone surfaces should be re-sealed after cleaning with this product.

LTP Solvex 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Light stripping, 8-10m2. Deep stripping, 5m2    Suitability: For stone, travertine, terracotta, slate, sandstone, flagstone, quarry tiles, glazed ceramics and porcelain You can use the LTP Coverage Calculator to confirm how much you will need of this product.   NOTE: Protect acrylic surfaces such as baths and shower trays from contact. Make sure to avoid prolonged contact with the joint as well if removing residues from epoxy grout.

LTP Porcelain Floor Tile Cleaner 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: 1L of LTP Porcelain Floor Tile Cleaner should be sufficient to wash an average floor of 20m2approximately 40 times  Suitability: Suitable for all types of porcelain and ceramic tile on both sealed and unsealed surfaces, as well as both polished and unpolished surfaces You can use the LTP Coverage Calculator to confirm how much you will need of this product. NOTE: For polished surfaces and highly glazed tiles, finish by buffing with a dry soft cloth or machine

LTP Porcelain Tile Protector 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Low porosity surfaces, up to 30m2 per litre    Suitability: For use on all types of textured porcelain tile surfaces You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Hard to remove, dried-on cement stains can be removed using LTP Grout Stain Remover or LTP Cement, Grout and Salt Residue Remover. Hart to remove stains from jointing compounds can be removed using LTP Solvex. 

LTP Mouldex Grout Cleaner 500ml

Colour: Clear Size (ml): 500ml Approximate Coverage: 5-15m2 depending on the size of the tile  Suitability: Can be used on natural stone and coloured grouting, however always test on an inconspicuous area before general application. You can use the LTP Coverage Calculator to confirm how much you will need of this product.   NOTE: Do not use with acid-based residual grout removers or other acid-based cleaners

LTP Cement, Grout and Salt Residue Remover 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Mild cases, up to 30m2. More severe cases, up to 10m2. Extremely severe cases, up to 5m2   Suitability: For all types of unpolished natural stone, porcelain, glazed ceramic, slate, quarry tiles, brick, terracotta and granite You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Not suitable for use on surfaces that are polished (i.e. polished marble, travertine or limestone). Any contaminated surface should be rinsed off immediately with plenty of clean water. Do not use when underfloor heating systems are in operation. Mask and protect any surface not to be cleaned.

LTP Crackle Glaze Protector 500ml

Colour: Clear Size (ml): 500ml Approximate Coverage: With 2 coats, this should cover up to 5m2    Suitability: For ceramic tiles that have a porous crackle glaze. To be used on crackle glaze tiles and grout joints You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Due to variations in crackle glaze tiles, always test the product first to ascertain the correct number of coats to be applied

LTP Grimex 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Mild cases, up to 50m2. More severe cases, up to 20m2. Extremely severe cases, up to 10m2   Suitability: Suitable for travertine, limestone, sandstone, slate, marble, porcelain, graine terracotta, quarry tiles, brick and external paving. Effective for removing oil, grease, ingrained dirt grime and old wax layers.  You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: This product should not be used for every day cleaning of floors or walls that have been sealed. Cleaned surfaces that have been previously sealed should be re-sealed after using this product. This should be done after rinsing with plenty of clean water, once surfaces have had sufficient time to thoroughly dry (minimum 24 hrs)

LTP Grout Stain Remover 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Mild cases, 30m2. More severe cases, up to 10m2. Extremely severe, 5m2  Suitability: Used to remove cement residues, grout stain, efflorescence and other similar deposits. This can be used in a dilute or concetrated form. Recommended for use on glazed and unglazed ceramics, slate, quarry tiles, brick, terracotta and acid-resistant natural stones. You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Not suitable for use on surfaces that are calcareous, sensitive to acids, or contain lime. Always rinse surfaces thoroughly with clean water after use.

LTP Mattstone 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: Per 10m2, lower porosity floors need around 1-2 litres, higher porosity floors need around 3-4 litres    Suitability: All types of natural and artificial stone, unglazed porcelain, sandstone, slate, marble, terracotta, quarry, brick and concrete. You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Following application, do not allow the surface to get wet and keep dry for a minimum of 3 days. Use in a well-ventilated area and do not breathe the vapours. 

LTP Colour Intensifier and Stainblock 1L

Colour: Clear Size (ml): 1000ml (also available in 5000ml) Approximate Coverage: Per 10m2, lower porosity floors would need around 1-2 litres, higher porosity floors would need around 3-4 litres    Suitability: For all types of natural and artificial stone, unglazed porcelain, sandstone, slate, marble, terracotta, quarry, brick and concrete. You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Do not allow surfaces to get wet, following application, for a minimum of 3 days. Use only in a well-ventilated area. Do not apply on floors with underfloor heating turned on as the product may dry prematurely. 

LTP MPG Sealer 1L

Colour: Clear Size (ml): 1000ml (also available in 5000ml) Approximate Coverage: 10-30m2 per litre depending on the surface porosity Suitability: For polished marble, porcelain, granite and encaustics You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Remove any factory-applied sealer or wax from the tiles before sealing. Ensure any under-floor heating is switched off when applying this product. Use only in well-ventilated areas and do not breathe in the vapours.

LTP Ironwax Satin 1L

Colour: Clear Size (ml): 1000ml (also available in 5000ml)  Approximate Coverage: 15-30m2 per litre (one coat) depending on substrate porosity Suitability: For travertine, slate, limestone, sandstone, bricks, terracotta, unpolished marble, porous quarries, terrazzo and concrete. Suitable for domestic and commercial use You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Not suitable for external use or wetrooms and shower enclosures. Avoid shaking bottle prior to use, frothing may lead to an inconsistent finish. Avoid extreme temperature. The product may not adhere to highly vitrified quarry tiles or ceramics. Avoid using strong detergents to wash treated surfaces. On higher porosity floor materials, LTP Mattstone H2O may be required.

LTP Glaze Protector 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: 30-40m2 per litre (one coat), depending on substrate perosity    Suitability: Interior use only, not for wetrooms or shower enclosures though. Retains the 'just washed' look on glazed ceramic, porcelain, unpolished porcelain and vitrified quarry tiles You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Not for use on wetrooms or shower enclosures. Do not over-apply as too many coats may cause unsightly build up and/or reduce the efficiency of the product. Hardens after about an hour but will take a further three days to achieve full hardness and become fully water resistant. Always test first to establish the correct method of application and optimum number of coats before general use. 

LTP Waxwash Aftercare Cleaner 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: 1L should be sufficient enough to wash an average floor of 20m2 approximately 40 times    Suitability: High quality liquid soap for all types of natural stone, slate, porcelain, terrazzo, concrete, quarry and terracotta surfaces. But this product can be used on most surfaces. You can use the LTP Coverage Calculator to confirm how much you will need of this product.   NOTE: On waxed or polished surfaces such as porcelain, granite and glass, finish by buffing with a dry soft cloth or machine

LTP Floorshine 1L

Colour: Clear Size (ml): 1000ml Approximate Coverage: 1L should be sufficient to wash an average floor of 20m2 approximately 40 times    Suitability: Recommended for use with tiled, wood and laminate surfaces You can use the LTP Coverage Calculator to confirm how much you will need of this product. NOTE: Use in place of your normal detergent. Do not mix with any other cleaning agent. Not suitable for highly polished tiled surfaces - for correct maintenance of this type of surface, use LTP Porcelain Floor Tile Cleaner or LTP Stonewash

LTP Grout and Tile Protector 600ml

Colour: Clear Size (ml): 600ml Approximate Coverage: 600 linear meters, depending upon the size of the grout joint and number of coats required. 5-25m2 of tile and grout, depending on the porosity and the number of coats required.  Suitability: Use as a 'top coat' to protect from penetration by water, dirt, oil, grease and limescale, making treated surfaces easier to clean. Ideal for use in wetrooms and shower enclosures.  You can use the LTP Coverage Calculator to confirm how much you will need of this product. The Technical Data sheet can be found here. NOTE: Do not use harsh abrasive cleaning agents. Clean treated areas with water and a mild PH neutral detergent like LTP Waxwash or LTP Stonewash. In some instances, it may be necessary to use a stronger cleaner to remove stubborn surface marks, in which case you may need to reseal treated areas.  Do not spray on to acrylic or stained surfaces such as cabinets and stained timber skirting boards. Mask and protect these surfaces before application.